Sunface / Fuzzface circuit analysis

 The Sunface is a Fuzzface slightly modified. 


Fuzz face is really a simple circuit design, as you can already tell by the number of components of the circuit: 4 resistors, 3 capacitors and 2 transistors! And of course two controls: fuzz + volume! As simple as that! But when we look at the circuit:


Fuzzface circuit
Fig.1 Fuzz face circuit, classic 60s original schematics
(made with Fritzing)

Not so easy to understand, isn't it?
Let divide this schematic in 3 sections:
Fuzz face circuit electronics
Fig.2 Fuzz face circuit, classic 60s original schematics
with different sections of the circuit
(made with Fritzing)


The first capacitor (C2, 2.2uF) filters the DC current at the entry of the circuit to avoid troubles with the next part of the circuit. This kind of capacitor (that you will find in a lot of circuits) is called a coupling capacitor. It also acts as a high pass filter, removing some bass frequencies. Enlarging its value will let more bass go through the circuit.

The gain amplifier section (blue part of the circuit) is a simple common emitter layout to amplify the signal. It has the maximal gain possible in this configuration: the emitter is directly connected to the mass, and the collector is directly linked to the base of the second transistor. It is a very classical layout that you will find in many many transistor based circuits, even if usually a resistor is present between the emitter of the transistor and the mass. This stabilizes the circuit, and allows a fine tuning of the transistor gain by creating a negative feedback. The second transistor is in the same layout, except for its emitter.

The main interest of the circuit is the feedback loop (in green). The emitter of the second transistor is linked directly to the base of the first one through a 100k resistor. A part of the current goes back to the first transistor, creating an amplification loop: current from Q2 comes back to Q1!
The counter reaction (therefore the gain) of the second transistor is modified by a variable resistor placed between the emitter of the transistor and the mass: the fuzz potentiometer! By diminishing its value, the quantity of current going to the mass increases whereas the amount of current going through the feedback loop is diminishing. If the value of the variable resistor increase, more current goes through the feedback loop: the base of Q1 receives more current, saturation increases.

The volume / output section (in red) is the simplest volume control that you can imagine: a 0.1uF coupling capacitor to eliminate DC current, and a volume potentiometer wired as a variable resistor. The output signal will be more or less important depending on the value assigned to the potentiometer.

So how is the Analog man version different? Here is an Analogman Sunface circuit schematic:
Analogman Sunface circuit
Fig.3 Analog.man Sunface circuit
(made with Fritzing)

The Analog.man version of this circuit introduces some little improvements to this circuit. First of all, a trimpot (wired as a variable resistor) is present at the input of the circuit before the 2.2uF capacitor. Thus, the entry impedance can be adjusted a bit. It plays the same role as a guitar volume pot, so you can adjust the fuzz gain, which is really useful for high output pickups for instance.

Another modification to the circuit is the 8.2k resistor that is replaced with a 2.2k resistor plus a 5k linear potentiometer. I prefer to use a 10k potentiometer so the original 8.2k value is reachable. This modification allows you to set the bias of the second resistor. It is useful in order to have the maximal gain, especially as the circuit is really temperature-sensitive.

Finally, some values are changed compared to the original circuit: the coupling capacitor is 1uF and the one before the volume pot is 0,01uF. The volume potentiometer is 250k. All together, this will remove a bit of low end, making it a brighter fuzz. This is probably done in order to compensate the deeper tone of the NKT275.

Nothing difficult, but still good improvements to the circuit !


References / to go further:
http://www.geofex.com/article_folders/fuzzface/fffram.htm 
http://fuzzcentral.ssguitar.com/fuzzface.php
http://www.electrosmash.com/fuzz-face
http://www.analogman.com/fuzzface.htm

Commentaires

Enregistrer un commentaire

Posts les plus consultés de ce blog

Klon Centaur mods and tweaks

Image
  Summary Klone centaur build (Aion refractor) Klon centaur circuit analysis Klon centaur mods and tweaks Klon centaur history and versions  Here is the schematic of the Klon Centaur: The Klon centaur circuit can be modded easily to modulate the gain, bass response or diode clipping. Lets see a few Klon Centaur mods together: Increase C14 value:  it is a very common mod to set the tone response a bit better. It allows a bit more bass to go through and make the Klon less "thin sounding". I usually use a 6.8nF capacitor, treble pot is thus more useable. Separate the dual gain potentiometer in two pots:  instead of using a double potentiometer, you can split each parameter with two 100k potentiometers. You can choose how much clean signal you will blend with the overdrive sound, or use only the overdrive part of the circuit. It is also useful for bass, if you want to let more bass goes through the circuit. I guess that the blend potentiometer on the bass soul food comes...
Lire la suite

Circuit analysis: Jan Ray (Timmy)

Image
 The Jan Ray overdrive is one of the many scandals that shook the boutique pedal community recently. Indeed, the Jan Ray has been proven to be a Paul C. Timmy slightly modified as we will see by studying the circuit. However, Vemuram pretended that it was an original design he made up listening to old Fender amps during 3 years... And sold the pedal at an indecent price for an analog pedal: 370 euros (400 dollars) ! This is a typical marketing strategy: "the price represents the quality", which is totally absurd for a basic electronic guitar pedal... He sold a lot of them whereas Paul C. produced the same pedal for 120 dollars. This a pedal that deserves to be cloned, and if you want to buy this sort of overdrive, go for the  Timmy ! Here is the schematic of the Jan Ray circuit as it is on the veroboard (a bit different from what you can find online, but functional !) Vemuram Jan Ray schematic (Made with Eagle) It is quite a classical layout, using the 2 OP-amps included in t...
Lire la suite

Klon Centaur circuit analysis

Image
  Summary Klone centaur build (Aion refractor) Klon centaur circuit analysis Klon centaur mods and tweaks Klon centaur history and versions For those who do not know the Klon Centaur yet,  it is an overdrive created in the 90s by Bill Finnegan and MIT engineers  (yes!), that is probably the "hypest" pedals of all. It was used by many guitarists, including Jeff Beck for instance. It is a three potentiometers overdrive: gain, volume and trebles, famous for the light crunchy tones it provides to your sound. It has also an excellent reputation as a buffer or clean boost. In fact, I have already made  Klon buffer PCBs  to use it in a patch box.  The Klon is a rather complex circuit.  It is quite weird because there are lots of informations and tests about this pedal online, however there are few informations about how the circuit works precisely. I have to remind you that the circuit was mainly conceived by electronics engineers from the MIT (and not by Bil...
Lire la suite