Klon Centaur mods and tweaks

 Summary


 Here is the schematic of the Klon Centaur:Klon Centaur Schematic
The Klon centaur circuit can be modded easily to modulate the gain, bass response or diode clipping. Lets see a few Klon Centaur mods together:
  • Increase C14 value: it is a very common mod to set the tone response a bit better. It allows a bit more bass to go through and make the Klon less "thin sounding". I usually use a 6.8nF capacitor, treble pot is thus more useable.
  • Separate the dual gain potentiometer in two pots: instead of using a double potentiometer, you can split each parameter with two 100k potentiometers. You can choose how much clean signal you will blend with the overdrive sound, or use only the overdrive part of the circuit. It is also useful for bass, if you want to let more bass goes through the circuit. I guess that the blend potentiometer on the bass soul food comes from this mod.
  • Diode clipping switch: you can choose between two sets of diodes with a simple DPDT switch. This is what I did with my Soul Food mod. There are not much changes between germanium and silicon diodes, however LED gave some nice results. There is much more headroom, it feels a bit like a distorsion!
  • Bass switch (madbean "fat" switch): this switch will affect the amount of bass that goes through the second OP amp. To do that, we can add a switch to choose between the 82nF stock capacitor and a 150nF one for C7.
    Klon bass switch mod
  • Bass contour mod: instead of using a switch, you can use a 50k potentiometer to blend the higher value capacitor in. You can also use a bigger value like 220 nF or even 1uF! However, you can see that this mod is only acting on the saturated part of the circuit, and not on the clean signal that is blend later. Thus, it is more hearable with high gain values... To have a proper bass knob, you can try to use a double potentiometer, and blend a higher value capacitor in parallel of C4 (68nF) too! I have never try that, maybe I will give it a shot at one point.
    Klon bass potentiometer mod
  • Using different OP amps: instead of the TL072CP, you can use different less noisy OP amps, or more "classic" overdrive OP amps. The simplest solution is to use sockets for OP amps, and try any double OP amp IC that you would like. To test: LM1458, OPA2132, LF353, JRC4558D... Any double OP amp can give you interesting results!
  • Increase gain: to have more gain on your unit, you can modify R10 resistor. It has a 2K resistor originally, and you can use a lower value to have more gain, or even a jumper!
  • Using the Klon Centaur with a bass: if you cant to use the Klon Centaur with a bass, you can change a few values to let more bass going through  (from Madbean pedals): C1, C3, C4 : 220 nF, C5 : 100 nF, C6 : 1 uF, C8, C13 : 1 nF, C7 : 330 nF, C11 : 6,8 nF, C12 : 56 nF, C14 : 15 nF. I also strongly suggest to separate the gain and blend knob (second mod), so that you can dose how much bass will go through the circuit. The Bass Soul Food actually uses this mod. Here is the traced scheme for our bassist fellows:
Klon centaur for bass schematic
  • 1994's specs switch: in 1995, Bill Finnegan slightly modified the circuit (see below). Most of the changes were not affecting the sound, except the addition of R11 (15k resistor), that was supposed to boost a bit the bottom mids. If you want to hear what that does to your tone, you can put a switch there to choose between the 15K resistor or a jumper.
I will try to do some videos of some of these mods.

There it is, this is the end of this post! I know it is dense, so take your time, and do not hesitate to ask questions by posting a comment! I this point, I am not totally sure about how each part of the circuit works, so do not hesitate to correct mistakes I could have made in the circuit analysis.

Did you like this article ? Thank me by liking the Coda Effects facebook page!


To go further
2009 document produced in 2009 by Martin Chittum from freestompboxes.org
Aion electronics building guide, well helpful and with a lot of informations about the Klon Centaur.
Refractor project page by Aion Electronics.
"Klown" Centaur page of the Revolution Deux website.
"Sunking" project from madbean pedals, another Klon clone with a bigger PCB for 1590BB enclosures.
Modded "Klown" centaur of the Revolution Deux website.
Website with pictures of Klon centaur, classified by serials
Manticore fx : lots of informations about the Klon
History of the Klon Centaur on Premier Guitar, with a Bill Finnegan interview.
Klone science on madbean pedal: frequency response plots of different klon clones

Commentaires

Enregistrer un commentaire

Posts les plus consultés de ce blog

JHS Superbolt / Supreaux Circuit analysis

Image
 JHS is not one of the most honest builders on the planet, and he is known for his ability to steal circuit designs from other builders. The Thunderbolt is no exception, and is in fact a really slightly modded Run Off Groove Supreaux.  Run Off Groove  is a community creating circuits for DIY people, and making it public through Creative Common license. There are many nice circuits there, take a look! JHS did not bother with the license and just copy it and started to sell it. The circuit is inspired by an old class A amplifier, the Supro 16T. It is a small 5W amplifier from the late 60s. It became quite famous, because like many other class A amplifier, if you push the volume really loud, the amp begins to distort in a really nice way. It was used in studio by many guitarists, especially by Jimmy Page who recorded several Led Zeppelin songs with it. Here is the schematic of the ROG Supreaux: And here is the JHS Superbolt schematic: You can see that it is basically the same circuit, wit
Lire la suite

Circuit analysis: Jan Ray (Timmy)

Image
 The Jan Ray overdrive is one of the many scandals that shook the boutique pedal community recently. Indeed, the Jan Ray has been proven to be a Paul C. Timmy slightly modified as we will see by studying the circuit. However, Vemuram pretended that it was an original design he made up listening to old Fender amps during 3 years... And sold the pedal at an indecent price for an analog pedal: 370 euros (400 dollars) ! This is a typical marketing strategy: "the price represents the quality", which is totally absurd for a basic electronic guitar pedal... He sold a lot of them whereas Paul C. produced the same pedal for 120 dollars. This a pedal that deserves to be cloned, and if you want to buy this sort of overdrive, go for the  Timmy ! Here is the schematic of the Jan Ray circuit as it is on the veroboard (a bit different from what you can find online, but functional !) Vemuram Jan Ray schematic (Made with Eagle) It is quite a classical layout, using the 2 OP-amps included in t
Lire la suite

Rub A Dub Reverb circuit analysis

Image
 A stompbox reverb is most of the time a digital effect, simply because an analogue reverb requires a spring or plate system that is way too big for a standard 125B enclosure format. Fortunately for us, a manufacturer called Belton provides Digital Reverb modules that can be used for such projects. They are declined in 3 types corresponding to the possible duration of the reverb: short, medium and long. This brick contains a rather complicated circuit with 3 PT2399 (numeric delay chip) that follow each other with really short delay time to act as a reverb. Bam! I told you it was kinda complex... They managed to make it smaller as possible with surface mounted components so we, small DIYers can use it at home to make our reverbs! It has 6 pins: Pin 1 should receive  a  regulated  +5V voltage Pin 2 should be connected to  power ground Pin 3 is the  input of the circuit Pin 4 is the  signal ground Pin 5 is the  output 1 Pin 6 is the  output 2  (for stereo applications) So it is like havin
Lire la suite